3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [creality-cr-6]

17 questions
3
votes
0 answers

Random Line on some 3D prints

I have been having an issue for a while now with my 3D Print that one of the layers will appear thicker than the rest. The line artifact will be on different height level. Also not all models that I would print would have this defect some will look…
DaveTheViking
  • 31
  • 2
3
votes
3 answers

Prints not sticking to bed or just not extruding?

I'm very new to 3D printing. When my printer was new, I got loads of really good prints, however, now they're all failing. I suspected that the nozzle was in bad shape, so I replaced it, but even now, the prints are still quite bad. I suspect that…
Jim
  • 163
  • 5
2
votes
1 answer

Shocks and enclosures

I have a Creality CR-6 SE running Community firmware. It's printing mostly well, in part because it's improvisationally enclosed (sheets of cardboard between it and the closes window to reduce draft, which was killing my prints on bad days). To make…
Mast
  • 217
  • 1
  • 11
2
votes
1 answer

Raising E-steps on my CR-6 SE makes the extruder choppy

I have the community edition of the firmware for my CR-6 SE printer installed on a BigTreeTech SKR-CR6 V1.0 board. This firmware has a nice E-step calibration guide you can use to easily get the correct step/mm value. However when I raise that…
inifus
  • 35
  • 7
1
vote
1 answer

CR-6 SE rebooting at fixed moments in print

My printer seems to be responding poorly to some of the prints I provide it with. At a certain time, usually after at least half an hour. For example, the print I tried today (twice) kept crashing somewhere after 52 minutes. Both times at the same…
Mast
  • 217
  • 1
  • 11
1
vote
1 answer

Creality CR 6 SE Z-axis issue

My new Creality CR6 SE was doing good but suddenly its Z-Axis (head extruder) randomly sometimes stays above the required configurations and sometimes below. For example after auto leveling when I adjust the Z-axis with paper under it, it aligns…
sairfan
  • 121
  • 2
1
vote
0 answers

Creality CR 6 SE firmware

I recently bought Creality CR 6 SE, I learned there are third party firmware available, I want to know which one is best known for CR-6
sairfan
  • 121
  • 2
1
vote
1 answer

How to restore languages to Creality CR-6 SE after firmware update?

I have been battling print issues since my purchase of a new Creality CR-6 SE. I chose to do a firmware upgrade to see if it's perhaps a patched issue. I used the Creality Download page and downloaded the zip containing the 4.5.2 mainboard firmware…
Dapper
  • 11
  • 1
1
vote
1 answer

Weird pattern on vertical surfaces on all prints

I recently received my Creality CR-6 SE printer and upgraded the controller board to a Bigtreetech SKR CR6 V1.0 and installed the latest community firmware. As you can see on the attached image, the corners have this weird elephant foot thing going…
inifus
  • 35
  • 7
1
vote
2 answers

CR6-SE fails to heat hotend to set point

TL;DR - Please help me rebuild my CR-6 SE so that I can move on Here's a link to the latest issue that I had to make proof of in a video: CR6-SE failed Basically, it's failing to reach/maintain temperature (set point of 240 °C, fails to heat above…
bigpow
  • 47
  • 8
1
vote
4 answers

CR-6 SE glass build plate - no lifting possible

I've been dealing with 3D printing for 1.5 years, but now own a CR-6 SE myself since the beginning of 2021. Most things are already quite clear but for 2 days I have had a problem with the adhesion of the prints. Nearly all prints I have done so far…
nioerd
  • 13
  • 4
0
votes
0 answers

Installing Creality CR6 SE Community firmware

I want to know how simple is it to install CR6Community firmware https://github.com/CR6Community/Marlin/releases I do not want to make low-level modifications for it. And also I want to know how simple is it to get back to official firmware? I want…
sairfan
  • 121
  • 2
0
votes
0 answers

Quantum PLA stops extruding, other PLA works fine

I recently tried to use Matterhackers Quantum filament and I've run into some issues and curious if anyone else has. I have a CR6-SE with community firmware, a regular Bowden tube with upgraded heatbreak (the metal tube that goes inside the heat…
Dennis Best II
  • 1
  • 1
0
votes
0 answers

Static electricity underneath the print with mystery adhesion and warping

Any idea what could be causing a static discharge on large prints? It seems that it's mostly visible when it's done and the print is being removed, it keeps zapping (can barely feel it. Small prints don't seem to be doing this. This leads me to…
PrinterBuddy
  • 1
0
votes
1 answer

Creality CR-6 SE heatblock replacement

Recently I broke the threads inside the heatblock of my CR-6 SE by tightening the nozzle too much (it seemed not deep enough). No problem - bought a new hotend extruder kit for around 35 euros. I put everything back together and it worked for some…
nioerd
  • 13
  • 4
1
2