3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [replacement-parts]

For replacement parts for 3D printers

When asking for replacement parts for 3D printers, which are either original branded, OEM, or alternative third party parts.

30 questions
13
votes
5 answers

Print only part (fraction) of a model

I've made a 9H-printing model tonight, and only a little part of it failed (because a support dropped off). I want to reprint only that little part. How can I do that in Cura? How can I tell Cura to generate a gcode file so only that little part…
Xenos
  • 323
  • 1
  • 3
  • 8
12
votes
2 answers

Printing Plastic Replacement Parts

On a number of occasions I've broken small plastic parts that are nearly impossible to replace but could easily be 3-D printed. The latest such mishap is the volume knob on the factory-installed radio on my car. I have little experience in 3D…
James
  • 249
  • 2
  • 7
9
votes
1 answer

Dimension SST Printer Broken parts

My company has an old Dimension SST printer that is out of commission due to a few broken pieces. I have contacted the Stratsys folk and they won't do anything until we purchase a multi-thousand dollar service policy. I also have a Makerbot that I…
Mjones
  • 91
  • 2
9
votes
1 answer

How long is an extruder's/nozzle's life?

I've been using a printer for several years now and I've never replaced any of my extruder hardware (nozzles, steppers, gears etc.). I was wondering how long you should expect your extruder hardware to last? Is it indefinite, or are there normal…
Diesel
  • 1,855
  • 2
  • 10
  • 29
7
votes
4 answers

Can a 3D printer make a 3D printer?

Could you use a 3D printer to make a 3D printer's parts? What is the most of a 3D printer that can be made this way? Could parts that break be replaced this way?
Muze
  • 1
  • 5
7
votes
3 answers

What voltage does the Creality Ender-3 run at?

I am pondering about buying a Creality Ender-3, and I am honestly confused about some reviews. Some claim it is running 24 V, one did claim it was 12 V, most don't mention it. Since I know about some issues with the clamps, if I get myself an…
Trish
  • 20,169
  • 10
  • 43
  • 92
6
votes
4 answers

What makes an extruder right handed?

I have been looking to buy a new extruder. One of the options I have seen comes in "right handed" and "left handed". What does this mean? How can I tell what my current extruder is, so I get the right replacement?
linuxdan
  • 1,289
  • 11
  • 27
6
votes
2 answers

Laser cutting on RepRap

I have seen some lasers attached to the RepRap platform for cutting but most seem to be cutting paper, balsa wood, or merely etching. If I were wanting to build a platform for cutting wood, similar to the wood framed or boxed 3D printers on the…
zkent
  • 347
  • 2
  • 5
6
votes
2 answers

What is this called? A tube flange bearing threaded for threaded pushrod

How should I describe this part which looks like a threaded flange so that I can research replacements? It is the gold piece in the middle of each photo. It is used to create a bed raiser in the FLSUN Cube 3D printer. It gets attached to a motor…
K Mmmm
  • 1,600
  • 11
  • 30
5
votes
2 answers

How to clean up my build plate for a new build surface?

My ender3 came with a BuildTak-clone surface, and as I was a little too vigorous in getting the print off the bed (I had failed to level right and printed a bit too tight to the bed, resulting in SUPER strong adhesion), I needed to replace…
Trish
  • 20,169
  • 10
  • 43
  • 92
5
votes
2 answers

What parts are suitable replacements for an Ender 3 Pro?

I'm new to 3D printing and I recently got my first 3D printer, an Ender 3 Pro by Creality. I've tried to find information about the type of nozzles should I look for. I'm trying to find stainless steel nozzles but there are so many models (M7, M8,…
iamroot
  • 53
  • 1
  • 3
5
votes
1 answer

What type of plug is this?

I'm not really sure what the type of plug on the heater cable is. Is it a Molex KK or maybe a JST PH? The printer is a Prusa I3 Hephestos (aka BQ Hephestos). It came with this "BQ HOT-END HEATCORE CLASSIC" hotend from the "BQ Witbox 1" extruder.
RomanTenger
  • 105
  • 9
4
votes
1 answer

Ultimaker Original temperature sensor replacement?

The title almost says it all. I was searching on websites like amazon.com and ebay.com for a replacement of the temperature sensor of my Ultimaker 1, but could only find replacements for Ultimaker 2 (PT100), but I know those aren't compatible. What…
Markus Appel
  • 392
  • 3
  • 8
3
votes
2 answers

Important build plate characteristics/qualities

I managed to tear my build plate trying to get some very stubborn plastic off it. I'll need to buy a new one, what characteristics are important for me to ensure it's compatable with my printer? I can think of: Dimensions Power…
BanksySan
  • 520
  • 2
  • 7
  • 20
3
votes
1 answer

How do you know when your SLA resin tray needs to be replaced?

How do you know when your SLA print tray has lost its non-stick coating? Are there visible or testable signs you can use to determine it is time to invest in a new resin tray? Is it best to count prints and estimate?
DMrFrost
  • 362
  • 1
  • 4
  • 16
1
2