3D Printing Stack Exchange
3D Printing Stack Exchange

Most Popular

more tags
1500 questions
5
votes
2 answers

What does a stand alone "T" index value do?

I'm using IdeaMaker for slicing my print objects. IdeaMaker start strings have a >T0< standing alone on one line and then >T1< on the next line. What does this accomplish?
Mouser
  • 51
  • 1
5
votes
1 answer

Slicer software capable of working with large filaments

I'm starting work on a very large 3d printer that uses very large filament. The idea is to house the entire thing in a shipping container and print things as large as cars. Filament will be some type of epoxy that is to be extruded out of a large…
henradrie
  • 73
  • 4
5
votes
1 answer

Replicator+ Motherboard Model

What is the make/model of a MakerBot Replicator+ motherboard? I'm assuming that the make is now MakerBot since they are now closed-source.
tbm0115
  • 6,234
  • 2
  • 18
  • 40
5
votes
2 answers

Using hardboard for 3D printer enclosure; what is the temperature rating of hardboard?

I am looking for the temperature rating for hardboard. I want to use that as the base for my printer enclosure. It has proven incredible hard get a ball-park figure from Google. So, what is the maximum safe temperature for a hardboard panel at…
rufo
  • 269
  • 1
  • 7
5
votes
2 answers

Prusa i3 Mk3 - Top layer wrinkles (not on buildplate)

Recently started using my kit Prusa I3 Mk3 and noticed that with large horizontal surfaces a wrinkling pattern is emerging. As you can see in the image the wrinkles seem to run parallel, the surface is 10 mm above the build plate with all bridges…
Paul V
  • 75
  • 2
  • 6
5
votes
2 answers

3D printed part sticking to the support layer

I am using a Flash Forge Creator, and when I print big parts (only in this case) I have about 25% of the bottom of the printed object sticking very hard to its support layer. And I spend a lot of time removing it with a cutter. Is there any clue or…
AMA1123
  • 101
  • 5
5
votes
3 answers

Filament moving around and not sticking to bed

I have only just set up my Anet A6 today. I am trying to print a calibration box, but the print is moving around the bed while trying to print. Any ideas how to fix this? The documentation is very vague. Basically I am very new to 3D printing. I…
Andrew Hawkins
  • 51
  • 1
  • 3
5
votes
1 answer

Infill failure when printing larger prints

I'm new to 3D printing an I just got a Creality Ender 3 and I think I'm getting some good results with small prints. However, now that I'm trying some bigger prints and I'm running into infill material excess. In the picture below I just printed a…
guidout
  • 193
  • 1
  • 6
5
votes
1 answer

Why can my printer display remaining time but OctoPrint can't?

The Prusa i3 MK3 displays the remaining printing time right from the beginning. Image: 3:38 remaining after 0% printing From about 8 prints until now, I would say that this time is quite reliable. Octoprint, however, does not display the…
Thomas Weller
  • 781
  • 10
  • 21
5
votes
1 answer

What calibration options should I look into given these defects

I printed a temperature calibration cuboid for Hatchbox 1.75 mm PLA, in 1 °C increments from 180 °C to 190 °C. I have two questions related to this image: I'm not seeing any difference in quality across the temperature range. Am I just way off…
kolosy
  • 591
  • 4
  • 12
5
votes
4 answers

How can I avoid jamming in the feeder?

Recently, at work we bought a Guider II printer from FlashForge. When we try to print models using a high resolution or models with a too high printing time, the feeder gets clogged. And the feeder is too hot. We have concluded that the feeder is…
Mauro Rivera
  • 53
  • 5
5
votes
4 answers

How fast can printer head move without damaging steppers?

Is there any risk of damaging stepper motors if I set too big travel speed? What is maximum safe travel speed? My printer is a German RepRap Neo. I currently use 120 mm/s. Is it safe to increase this value to 200 mm/s? What would my printer do if I…
J K
  • 153
  • 4
5
votes
1 answer

LCD full graphic smart controller, no character display and screen blinking

After uncommenting the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER, the display is blinking and no characters are shown on the screen, I have already switched the cables between EXP1 and EXP2, but it did not succeed.
David Souza
  • 133
  • 1
  • 5
5
votes
5 answers

Difficult to remove support material

I'm having a lot of difficulty removing support material without damaging the print. Are there any tips/tricks to doing this or is it just a case of sanding, cutting, chopping and then cleaning it up as best I can? Settings Printer: Monoprice…
BanksySan
  • 520
  • 2
  • 7
  • 20
5
votes
2 answers

How Do Tool Path Algorithms Decide Which Direction to Print a Closed-Loop Polygon

I understand how slicer programs create sets of closed-loop polygons to print on a layer-by-layer basis. For a given closed loop polygon which needs to be printed, the tool path generator will know the coordinates and how those coordinates are…
Thetravellingfool
  • 328
  • 1
  • 7
1 2 3
…
99 100