3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [ultimaker-cura]

Questions about the slicing program called Ultimaker Cura.

For questions regarding the use or troubleshooting of the slicing software Ultimaker Cura which was formerly known by Cura solely before the re-branding. It is developed by Ultimaker together with the community and works as an open platform to support most 3D Printers.

383 questions
17
votes
2 answers

In Cura, can I make my top and bottom layer be all perimiters?

I'm using Cura to slice my prints. I've noticed that when printing the bottom layer (and also the top layer, if it's flat), it first prints three walls, then fills in the middle by moving back and forth in straight lines. I've noticed that for my…
N. Virgo
  • 1,489
  • 1
  • 14
  • 25
15
votes
4 answers

Why is it conventional to set line width > nozzle diameter?

I recently became curious about the Line Width setting in Cura and why one might change it if they aren't using different size nozzle. Since I've gotten my Ender 3, I've always kept the line width equal to my nozzle size (0.4 mm). I've looked around…
ifconfig
  • 851
  • 4
  • 12
  • 29
14
votes
1 answer

How to build CuraEngine?

I've been trying to build CuraEngine on Ubuntu following the Github instructions. The problem is that it lists some requirements: Clone the CuraEngine repository; Install Protobuf (see below); Install libArcus. I'm not sure where should I install…
Jorge Cuevas
  • 323
  • 2
  • 7
13
votes
5 answers

Print only part (fraction) of a model

I've made a 9H-printing model tonight, and only a little part of it failed (because a support dropped off). I want to reprint only that little part. How can I do that in Cura? How can I tell Cura to generate a gcode file so only that little part…
Xenos
  • 323
  • 1
  • 3
  • 8
13
votes
3 answers

Cura: set z-offset

I'm having a Prusa i3 derivative printer with a capacitive sensor for the z-axis. It switches a tiny bit before the nozzle hits the print bed and hence needs a z-offset to be configured. In Slic3r I have configured the z-offset to -0.1 on the…
Thomas S.
  • 903
  • 4
  • 9
  • 21
12
votes
2 answers

Cura not allowing full print area to used

Cura does not seem let the full print area to be used. My printer is a Lulzbot Mini. The design illustrated below can be found here.
QwertyChouskie
  • 307
  • 1
  • 3
  • 9
12
votes
6 answers

Danger in 3D printing over a lithium ion battery

So I bought a Lulzbot Mini a couple months ago and finally downloaded Ultimaker's version of Cura... Boy... have I been missing out... One feature Ultimaker Cura implemented that I've been looking for is a "pause at z-height" feature…
K Mmmm
  • 1,600
  • 11
  • 30
12
votes
2 answers

How to configure Cura to run the Z probe before heating

I'm using Cura as my slicing/printing software and I just started using the BuildTak printing surface. The BuildTak is damaged by pushing a hot nozzle into it and my printer's (Robo3D R1+) autoleveling feature works by pushing the nozzle into the…
Nir
  • 2,401
  • 4
  • 18
  • 32
11
votes
3 answers

Platform support up to a certain Z height in Ultimaker Cura/G-code

Ultimaker Cura offers a platform support type of “touching buildplate” which enables the printer to only make a raft for parts of the object that should be touching the build plate. It also offers “everywhere” for any object that might be hanging…
K Mmmm
  • 1,600
  • 11
  • 30
10
votes
5 answers

Writing G-code : swiping at start of print

Ok, I did it, I ordered myself an Ender-3, a genuine 24V e3D hotend, inductive sensor and some better tubing/clamps to cope with the problem the CR10/Ender line has occasionally. But now I need to fix up my Cura for the machine coming in. The start…
Trish
  • 20,169
  • 10
  • 43
  • 92
9
votes
1 answer

Extruder doesn't retract on inner wall lines thereby causing stringing

I am trying to stop the stringing that occurs on one of my prints, I have set it so that it retracts the filament which does stop it during the extrusion of the outer wall layer, however when it comes to print the inner lines of the section it does…
Liam
  • 669
  • 4
  • 11
  • 19
9
votes
3 answers

How to set the Z home offset

I have what I thought would be a simple question. I don't have an auto leveling probe, I do my leveling manually with 4 screws and a piece of paper (I measured the thickness to 0.1 mm). For the longest time I would have trouble with the first layer,…
Matthew Goulart
  • 193
  • 1
  • 1
  • 3
9
votes
4 answers

Seemingly random lines on the surface

I'm getting seemingly random lines scattered across the top surface of my prints: Printer: Anycubic i3 mega Slicer: Cura 3.2.1 Printer chosen in Cura: Prusa i3, Gcode flavor changed to RepRap Cura Profile: Fine, "Outer before inner walls"…
AndreKR
  • 271
  • 3
  • 10
9
votes
3 answers

Is there a way to save a multi part print if one fails?

I'm printing 6 separate parts in one go, after 4 hours of printing one part failed, but the other 5 are printing nicely. Is there a way to prevent the print from printing the failed part and continue printing the other 5 parts. I'm using Cura and an…
Nerdroid
  • 193
  • 5
8
votes
4 answers

Trouble printing small thin pole

3D-printing newbie here. I have a Geeetech's Prusa i3 mk2 B. I'm trying to print this: https://www.thingiverse.com/thing:1358311 That's a mold, with 2 external parts and a core. The exterior prints wonderful. But the core is too messy. Take a look…
Daniel Cantarin
  • 183
  • 1
  • 4
1
2 3
…
25 26