3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [laser]

Lasers of low power can be used as measuring tools in a 3D printer environment, but higher powered ones can be used to engrave materials if mounted as a 3D Printer's tool.

19 questions
9
votes
6 answers

Linux software for laser engraver

I am searching for a Linux software to control the 3000 mW laser engraver depicted below. It's a common model you'd find on AliExpress, Banggood, etc. under different brand names. I have already tried nejePrint, LaserWeb, and EzGraver, but they…
typo
  • 926
  • 1
  • 8
  • 13
7
votes
2 answers

Convert 3D printer to laser engraver

Can you convert a 3D printer to a laser engraver? If so is there a specific thing I have to buy?
Varun W.
  • 297
  • 1
  • 10
7
votes
2 answers

laser is engraving the negative space

I am using LightBurn to laser engrave on wood. I am just trying to print some letters. In the softwares preview the output looks correct. The black part is where the laser should burn and the red part are traversal/scan lines When i actually print…
codeNinja
  • 183
  • 1
  • 8
6
votes
1 answer

Add a laser module to Reprap Guru Prusa i3

I have a Reprap Guru Prusa i3 v2 3D printer. Here is a link to the 192 MB manual. And here is the link to the resources page for the Reprap Guru. Page 58 of the manual discusses electronics. I purchased a 5.5 W laser from an online resource…
codeNinja
  • 183
  • 1
  • 8
6
votes
2 answers

Laser cutting on RepRap

I have seen some lasers attached to the RepRap platform for cutting but most seem to be cutting paper, balsa wood, or merely etching. If I were wanting to build a platform for cutting wood, similar to the wood framed or boxed 3D printers on the…
zkent
  • 347
  • 2
  • 5
4
votes
1 answer

Laser Engraver with Smoothie, RAMPS 1.4 or AWC708C?

I have an old laser engraver that runs from Windows 98SE and DOS-6. Yup, still works fine but a pain as I regularly have to open it up and unplug and re-seat all the ribbon connectors. Fifteen of them and I tire of that fast. I am thinking of…
LinuxFerLife
  • 173
  • 1
  • 1
  • 3
4
votes
4 answers

Running laser on my printer

I am trying to control a laser with the fan (D9) and ran into problems. So I tried P44, no good then P6 also not good.\ What my problem is I am trying to "burn" a group of vertical lines spaced about 0.75" apart, and randomly the drive to the laser…
Pomonaill220
  • 101
  • 5
4
votes
1 answer

Laser LA03-5000 wiring to RAMPS 1.4

I'm totally lost. I have been searching about two days how to correctly wire Blue Laser LA03-5000 to RAMPS 1.4 board. This laser has 12 V input and separates PWM/TTL wires. I have found out how to control laser with no PWM (just hook it to D9 same…
Fires_CZ
  • 41
  • 2
3
votes
1 answer

Laser engraver on Ender 3 without taking important ports

I'm contemplating buying a laser engraver attachment for my Ender 3 Pro. Either the Creality official one or the Comgrow version. When scanning the respective web pages/answers on here and YouTube videos, it seems like you usually unplug cables for…
Joseph Crozier
  • 360
  • 4
  • 14
2
votes
1 answer

Laser engraving software for Boxzy 3D printer

I have a laser-engraving "head" for one of my 3D printers (a Boxzy, so it's designed for it, not just strapping a random laser onto something), and I'd like to try using it to, well, engrave something. So: Can anyone point me to some control…
TextGeek
  • 3,181
  • 2
  • 12
  • 32
2
votes
0 answers

Display locks when executing G-code for laser cutting using Marlin on RAMPS board

I'm working on a Laser cutter. I’m using the RAMPS 1.4 and Marlin software. To make the Marlin software work with a laser I’m inspired by this blog from dreammakercnc: Marlin Firmware modification for Laser Control My plan is to use Inkscape to…
Tafel Dekker
  • 21
  • 1
1
vote
1 answer

GRBL with low feed rate not working

I have a cheap 3000 mW laser cutter that I'm trying to cut 3 mm black acrylic. I'm lowering the feed rate to try to get it to cut in one pass. I have the G-code for a small circle (16 mm) but it seems any feed rate below about 25 mm/min is being…
Nick Wallace
  • 31
  • 2
1
vote
0 answers

Comgrow Mini Laser Engraver - Adding laser to Windows laser control software

I recently bought a Mini Desktop Laser Engraver by Comgrow. So far, the limited functionality of their iOS app has been fine for little trinkets for testing. Pretty good product for the cheap price. However, the technical specifications specify…
R3TURN-0
  • 11
  • 1
1
vote
0 answers

Why is a mold required in isostatic pressing after performing Sintering

After an a object is formed through direct laser sintering, as a post-processing procedure the object is sent for hot-isostatic pressing, In hot isostatic pressing the sintered object is placed in a mold and then pressure and heat are applied. I was…
Somanna
  • 121
  • 3
1
vote
1 answer

Is it possible to attach a laser engraver to a SLA / resin 3D printer?

While trying to figure out if I should start 3D printing with FDM (Creality Ender 3) or with SLA (Elegoo Mars), I got hooked on the bonus feature of attaching a laser upgrade on the 3d printer to make paper cutouts and cards. I read that its quite…
user19928
  • 11
  • 1
1
2