3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [skr-v1.3]

15 questions
7
votes
1 answer

How to wire P.I.N.D.A. v2 to an SKR V1.3 board?

I bought a BigTreeTech SKR v1.3 main board and a P.I.N.D.A v2 for my P3Steel MGN. Does anyone know to wire them together and which part in Marlin 2 do I need to change?
Jack Iai
  • 71
  • 1
  • 1
  • 2
5
votes
2 answers

Setting Junction Deviation in firmware has no effect

I have built a 3D printer with Marlin bugfix-2.0.x forked from github. I am attempting to set the default value for junction deviation so that I don't have to change it through the printer's screen/interface every time I power cycle the printer, but…
Chris Ostmo
  • 153
  • 1
  • 5
4
votes
2 answers

G28 ignoring Z-Probe X/Y Offsets

I recently installed a SKR 1.3 Board with a 3DTouch-Probe on my Creality Ender 3 Pro. The probe works, G29 does its magic, but: If i issue a plain G28, the hotend first homes X and Y like before the Z-probe. The probe is now next to, not above,…
Odious
  • 41
  • 2
4
votes
2 answers

Getting wrong measurements on my Kossel Linear Plus after installing SKR 1.3 with Marlin 2.0

So I've switched the Trigorilla board in the printer with a SKR 1.3 with TMC2208 drivers and installed the latest Marlin 2.0, with a config based on this one. You can find the Configuration.h here, the only thing I changed in Configuration_adv.h was…
Metalfreak
  • 126
  • 6
4
votes
3 answers

Bigtreetech upload stalled after uncommented REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER

I recently bought a BigTreeTech SKR V1.3 and uncommented REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER and clicked the upload button but faced an error that says: Marlin\src\lcd\ultralcd.cpp:767:9: error: 'touch_buttons' was not declared in this…
William Jerome
  • 61
  • 2
3
votes
1 answer

What UART port to use for RPi GPIO pins on an SKR v1.3 board

I have a Bigtreetech SKR v1.3, and I'm trying to connect a Raspberry Pi to the board using the RPi's GPIO pins as opposed to using a USB connection because space is limited within the case of CR10S Pro. I watched this youtube video where he explains…
ipatch
  • 131
  • 5
2
votes
1 answer

Will the TMC2130 V3.0 stepper driver work with the Ramps 1.6 Plus board?

I want to buy the board Ramps 1.6 Plus. The description in the link says that is compatible with the driver TMC2130, but I found that there are two versions soldered in SPI mode. BIGTREETECH TMC2130 V3.0. Where the diagnosis pins are soldered as…
ChesuCR
  • 157
  • 2
  • 12
1
vote
1 answer

Auto bed leveling offset issue

I'm using an Ender 3 with a new upgraded board SKR 1.3 Marlin bugfix 2.0 auto bed leveling I use EZABL. for the EZABL I followed their tutorial for Marlin 2.0 since I don't use the unified firmware. Offset info : #define NOZZLE_TO_PROBE_OFFSET { 50,…
Félix Labelle-Thériault
  • 13
  • 3
1
vote
2 answers

How to have double extruder and double Z motor on a 5-driver board?

We are using the Board SKR 1.3 with the following pins: /** * Trinamic Stallguard pins */ #define X_DIAG_PIN P1_29 // X- #define Y_DIAG_PIN P1_27 // Y- #define Z_DIAG_PIN P1_25 // Z- #define E0_DIAG_PIN …
David Souza
  • 133
  • 1
  • 5
1
vote
2 answers

Partial underextrusion in walls

I'm facing weird "pillars" of underextrusion on outer walls of my XYZ test cube. On the pictures below I`ve printed PLA test cubes with a 0.4 mm nozzle, 0.2 mm height and 210/50 °C hotends/bed temperature. Gaps are appearing in walls parallel to…
Luka Baryshych
  • 11
  • 3
1
vote
1 answer

Switch nozzle contact probe auto leveling with Marlin 2.0

I have a Robo R1+ which uses the nozzle contacting the glass print bed to level the printer. When the print head strikes the bed the Z-min endstops open signaling that the bed is touched. I recently upgraded from an Arduino to an SKR 1.3 running…
henradrie
  • 73
  • 4
0
votes
0 answers

Hotend functioning inconsistently. PID completed normally, heating to quickly or not at all on print start up

I have a Xvico X1 printer which I had previously installed an SKR 1.3 on running Marlin, which was functioning normally. For Christmas I got a BLTouch, a heated bed and a Raspberry Pi for it, so I also installed a new 24 volt Meanwell PSU to power…
westph21
  • 1
0
votes
0 answers

Error:Printer halted. kill() called! SKR 1.3 TFT35 3.0

I am trying to fix the very last error on my printer (custom built). Error:Printer halted. kill() called! This error occures about 5-10 minutes into a print (XYZ Cube) and usually after finishing the second layer. All temperatures are working as…
user3310078
  • 1
  • 1
0
votes
0 answers

Printer froze mid print, stepper motor driver and MCU extremely hot afterwards. MCU seems dead now (?)

A strange problem occured while 3D printing. I've been printing for a long time now, and I consider myself fairly expeienced. normally, with every problem I've encountered with my printers (Anet, Ender, Prusa), there's always an answer online.…
Harel Thapro
  • 31
  • 2
0
votes
0 answers

LV8729 on kossel issues with print dimensions (steps)

I've installed the an LV8729 on a kossel, configured with SKR 1.3 and marlin 2.0 with all the jumpers configured in the same way for 16 micro steps for X Y Z axis. Everthing seems fine the printer running well. I notice when I print, some tests…
mastervv
  • 131
  • 1
  • 3