3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [skr-mini-e3]

19 questions
5
votes
0 answers

BLTouch not probing all points and motors making really loud noises since rebuild of latest Marlin (new hot end installed and BLTouch)

Please listen to this video, which illustrates the issue, with the sound on. Link to configuration.h and configuration_adv.h Machine Ender 3 Pro, New E3Dv6 hotend on a BMG Wind (all has been working and printing PLA, PETG, and TPU fine until I…
John Spencer
  • 151
  • 1
5
votes
2 answers

What can I do to remove the rounded corners using Junction Deviation?

I recently upgraded my Creality Ender 5 with an SKR Mini E3 V2.0 running Marlin 2.0.7.2. The printer has also been modified with an all-metal hotend and a direct drive conversion kit that uses the extruder stepper motor. In test prints of the XYZ…
user3883001
  • 51
  • 1
  • 1
  • 3
4
votes
0 answers

Connecting 128x64 OLED to BIGTREETECH SKR mini E3

I'm trying to connect a 128x64 OLED display with the SH1106 driver for the BIGTREETECH SKR mini E3 printer controller board which uses the 32 bit STM32f103RC MCU. Note that it works fine with my RAMPS 1.4 board but when I compile it on PlatformIO…
Oliver
  • 41
  • 2
2
votes
1 answer

BLTouch clone will not deploy, stow, or deploy when homing or auto leveling

I have 2 printers, an Artillery Sidewinder X1 and an Ender 3 that both have BLTouch sensors installed. This post is about the one (BLTouch clone, the probe is a Smart v3.1 sensor) installed on my Ender. My problem: I recently upgraded from…
Artichoke
  • 179
  • 1
  • 13
2
votes
2 answers

Why would all of the Ender 5 Pro's axis motors (X, Y and Z) stop being able to move (all at once)?

I have a Creality Ender 5 Pro which has been working properly for some time. During my last print, the axis motors just suddenly stopped working while the extruder motor continued to work properly. In fact, when I connect the extruder motor wire to…
Mahlomola Daniel Cwele
  • 51
  • 4
2
votes
1 answer

While heating, BLTouch mesh data gets worse and worse the more times you probe

The title pretty much sums up the issue. It was happening before moving to an SKR Mini E3 V1.2 and is still happening with the new board. If I run A G28, then a G29 - while not heated - I will get some mesh data (poor mesh data because I haven't…
DreamingInsanity
  • 31
  • 5
2
votes
1 answer

BigTreeTech mini e3 V1.2 endstop installation

I recently purchased a BigTreeTech mini e3 V1.2 controller for my custom built 3D printer (as opposed to an pre-purchased ender 3). In doing so, I ran into the problem that the endstops I have been using have three wires: Power, Ground, and signal.…
Jack Hasselbring
  • 89
  • 1
  • 6
2
votes
0 answers

How do I install the USB drivers for Bigtreetech's SKR Mini E3 v1.2?

I want to install the USB drivers for the BIGTREETECH SKR Mini E3 v1.2 from the GitHub page but I don't know how to proceed. Any help will be greatly appreciated.
Liam
  • 669
  • 4
  • 11
  • 19
1
vote
0 answers

M503 command is reporting "Maximum feedrates" with duplicate and empty values: M203 X200.00 Y200.00 Z5.00 E Y1000.00 Z100.00 E5000.00

I'm pretty stumped on this one. Investigating an issue I was having with an OctoPrint plugin, I've come to realize my M503 command is reporting duplicate and empty values. This is not an issue with the plugin, but an issue with the native M503…
calisoup
  • 11
  • 3
1
vote
0 answers

Ender 3 Pro with BLtouch + BigTreeTech Auto level not compensating

As the title says, I have an Ender 3 Pro + BLtouch v3.1 and BigTreeTech SKR mini E3 v2.0. I have the SKR loaded with "firmware-bltouch-for-z-homing.bin" but my printer does not seem to be auto leveling. I'm fairly new to 3D printing and I have no…
Tyler
  • 11
  • 2
1
vote
0 answers

Printer is using BLTouch to home but it is not using it to auto level

I have recently set up my Ender 3 with an SKR MINI E3 V1.2 and a BLTouch which I have been using for a while. After many troubles with compiling the firmware, I managed to compile and upload the firmware; enabling BLTouch and changing the…
DreamingInsanity
  • 31
  • 5
1
vote
0 answers

Print from card not showing on new SKR mini e3 v1.2 card

I am a newbie with a 3 months old Ender 3 Pro, my first one. I purchased, installed and loaded a new SKR Mini E3 V1.2 mobo. The LCD panel lit up as usual without problems. I selected 'print from card' which showed the micro SD card had 2 files,…
Denzil Cypret
  • 11
  • 2
1
vote
1 answer

Different Probe Z offset for G28 and G29

After trying to solve this for the whole weekend I've run out of ideas. I've fitted an BLTouch to my Ender-3 with an SKR mini e3 V2.0 board, firmware is Marlin 2.0. My issue is the following: when I do autohome (G28) it uses the Z-Probe (BLTouch)…
Daniel Echt
  • 21
  • 5
1
vote
1 answer

Thermal runaway triggers when raising temperature amid cooldown

I've noticed an interesting behavior on my Ender 3 with SKR Mini E3 mainboard and Marlin 2.0.x bugfix firmware. (otherwise, all other hardware is entirely stock) After the hotend/bed are commanded to cool down, e.g. after a print completes, I have…
ifconfig
  • 851
  • 4
  • 12
  • 29
0
votes
0 answers

Max31855 with SKR Mini E3 V3.0

I finally was able to get the temperature from the max31855 board and now I am running into another issue. When I power up my printer (Ender 3) it shows the temperatures for both the bed and hot end. A few seconds later I get the error beeping with…
Floyd Dameron
  • 1
  • 1
1
2