3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [filament-jam]

10 questions
5
votes
2 answers

Clogging from heat creep, but only in the nozzle itself?

I have an all-metal V6 hotend clone that has worked in the past, but recently will clog very easily. I've tried the following to address it: Clean/replace the nozzle (0.4 or 0.5 mm, nozzle is hot-tightened) Ensure nozzle is tightened against the…
Mandias
  • 161
  • 5
3
votes
3 answers

Filament Jamming in Hotend. Why?

This has me stumped. I had been printing normally until this happened. Below is an expurgated version of my headache over two days. Some help would be appreciated. Printer is Hypercube Evolution (CoreXY) using Bowden tube and eSun PLA+ filament.…
Ramblin' Sid Rumpo
  • 183
  • 6
2
votes
0 answers

Ender 3 Pro extruder keeps clogging

I'm fairly new to 3D printing and looking for help. I have an Ender 3 Pro and it's been working great up until about a week ago. When I preheat the extruder, the nozzle gets hot as it should, but it keeps jamming mid-print. About an hour in, the…
Megan Oliver
  • 21
  • 1
2
votes
1 answer

Prusa i3MK3S+ layer skip with polycarbonate (overheating?)

On the last couple of polycarbonate prints with my Prusa, one or more layers have been completely skipped (i.e. no material extruded). The rest of the print is fine save some minor warping. I'm printing in an enclosure that gets up to ~60 °C with…
TreeBarkEater
  • 162
  • 14
2
votes
2 answers

PLA Jamming- is the heat break too hot or too cold?

I’m getting nothing but jams with a new BCN3D Sigma R19 printer, printing PLA at 195 °C, two brands (BCN’s own brand and Monoprice orange). 6.5 mm retraction, as used in BCN’s PLA profile. Using their fork of Cura. Full enclosure, but it gets maybe…
ChinchillaWafers
  • 455
  • 2
  • 10
2
votes
1 answer

Filament getting stuck/nozzle is clogged

For some reason on my Raise 3D N2 plus with a Bondtech-Extruder I am sometimes seeing filament jams and sometimes it prints without any issues. I am using PLA at 215 °C. When the filament is jammed I have to pull it out, remove the tip, and then I…
DerDrucker
  • 21
  • 3
1
vote
1 answer

Filament Spool Stalls Extruder Motor Destroying Print

I am having the frustrating problem where my extruder motor starts skipping steps and stops extruding simply because my filament is wound too tightly. There are some parts of my filament that are so tightly wound that even I have to put some effort…
DragonflyRobotics
  • 203
  • 1
  • 6
1
vote
3 answers

Filament jam on the tube entrance

I have a problem in regards to filament jam, however I don't think that my case is any related to the extruder nozzle. After 30 to 40 minutes printing my filament bends and get stuck on the tube entrance. To print a nut wheel which comes as a demo…
Hola Soy Edu Feliz Navidad
  • 230
  • 2
  • 8
0
votes
0 answers

Anycubic Vyper filament loading problems

I recently acquired the Anycubic Vyper, and it's been working fine, until a few days ago. The filament extruder stopped working properly, as in it would extrude an amount of filament, before making a click/grinding sound, and then stopped…
Chinatown
  • 1
0
votes
0 answers

E3D V6 hotend gets jammed very frequently

In the past couple of weeks, my V6 hotend gets jammed very frequently. The nozzle is 0.4 mm and the printer is a D-Bot. Here are some of the things I have tried so far, Switched between the original and a clone and both get jammed. Tried different…
electrophile
  • 356
  • 4
  • 11