3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [skr-v1.4]

13 questions
2
votes
1 answer

Will my 3D printer significantly get quieter after upgrading from Creality board 2.5.2 to BTT SKR Turbo 1.4

I have a Creality CR10 v3, which includes a board v2.5.2 with built-in TMC2208 stepper motor drivers. I have read that it is still 8-bit (I thought that advertising a "silent board" meant it was 32-bit) and that upgrading to a 32-bit will improve a…
Myoch
  • 175
  • 6
2
votes
1 answer

(SKR 1.4 Turbo, TMC2209 Drivers) - Power supply has 4 output, but board only 2 input

I have recently purchased an SKR 1.4 Turbo which I intend to add to my P3Steel printer. I have an old power supply which appears to have dual outputs [COM COM +V +V]. I want to connect this to the board but the board only has a +V -V connector. The…
raven-king
  • 121
  • 2
2
votes
1 answer

Is it possible to run 2 Ender 3's off one power supply?

I have 2 Ender 3's and I am limited to wall sockets to power both the printers at the same time. So I was wondering if it was possible to wire both the printers to a single PSU? As the printer uses a single xt60 connecter for power to the mainboard,…
MeddlingSpy
  • 21
  • 1
2
votes
1 answer

Extruder motor does spin - but not while printing

I hope someone can poke me in the right direction, I´ve been failing to find a way around this problem and trying for about a week. My setup is pretty custom, I am using a BTT SKR 1.4 Turbo with TMC2208 driver and a BTT TFT V3 display. At the…
Spudermann Webz
  • 23
  • 5
2
votes
1 answer

X axis doesn't lift after levelling

So, I recently installed an inductive sensor to my 3D printer for auto bed levelling and now I'm stuck on Z probe offset as it doesn't seem to do much apart from changing number is given on display for the Z-axis. On tutorials that I watched, after…
Potato Lord
  • 31
  • 2
1
vote
0 answers

TMC2208 v1.2 stepper motor drivers not detected on SKR 1.4 turbo with RepRap firmware

I've upgraded my board to SKR1.4 Turbo with RepRap firmware. Everything works, but motors move double the request. M112 reports them as 'no-driver-detected'. M112 === Diagnostics === RepRapFirmware for LPC176x based Boards (biquskr_1.4)…
Chris Parussin
  • 11
  • 1
1
vote
1 answer

TMC2100 stepper motor drivers not detected on SKR 1.4 turbo with RepRap firmware

I've upgraded my board to SKR1.4 turbo with RepRap firmware. Heated bed and heated nozzle work, but motors do not move. OctoPrint reports them as 'no-driver-detected'. Send: M122 ... Recv: Driver 0: position 67347, no-driver-detected Recv: Driver 1:…
Ivan Gankevich
  • 21
  • 2
1
vote
1 answer

Ender 3 + SKR 1.4 + Marlin 2.0.x bugfix - what bed size/min/max positions should I use?

On my Ender 3, it seems that the Y-axis can only move forward 220 mm after which the carriage will hit the tensioner. This seems repeatable so I don't think it's a hardware issue (unless it's expected that the nozzle can reach all the way to the…
Alex Dow
  • 111
  • 2
1
vote
2 answers

Can I adjust print speed on the fly?

I am running an Ender 3 pro with an Octoprint connected. I accidentally set the print speed too slow in Cura and the print will take very long. Is there a Marlin command I can issue to the printer to speed it up without stopping the print?
Jackie
  • 143
  • 1
  • 1
  • 6
1
vote
2 answers

SKR 1.4 Turbo - Withhout SD-card reader, bricked?

Unfortunately and regrettably. Whilst trying to install and fit an SKR Turbo 1.4 Turbo Motherboard into 3D printer body, I managed to break the SKR 1.4 Turbo Motherboard SD-card reader. The card reader is not flush and protrudes from the board. It…
D_MAN
  • 11
  • 1
1
vote
1 answer

How to correct XY mirroring?

So I made a 3D printer from scratch. It is a RepStrap based on a Prusa i3 running Marlin 2.0.x. It prints fine and accurate, but, The trouble is that the XY plane is mirrored and I don't know how to solve this. I'm using Marlin 2.0.x on an SKR 1.4…
DDecoene
  • 111
  • 2
0
votes
1 answer

Diagnosing non-functional steppers (Ender 3)

I was upgrading my (already very modified) Ender 3 with a geared extruder, and figured instead of re-flashing the firmware, why not switch the extruder phase on the cable? I accidentally shorted the two coils together instead of swapping within one…
Brendan O'Connell
  • 1
-1
votes
1 answer

3D printer homing issue, nozzle damaging the bed when printing

I have a custom Cartesian style 3D printer. The controller board has been upgraded to a BIGTREETECH SKR V 1.4 Turbo. This is a 32 bit board. Marlin 2.0.3 seemed to build and install with less issues than others. I'm using VS code to work with…
Fz6r Rider
  • 1